[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[jamsat-bb:5073] StenSat不調 DTMFコマンド
JJ1WTK 坂本です
DHX> Wでは、DTMF信号に対して衛星からの反応があると、Web.で
DHX> 受信レポートを公表しているようですが本当でしょうか?
そのような内容の報告がいくつかあるのですが、
Hankは、それは自局がStenSatに向けたアップリンクの
スプリアスを、ダウンリンクと勘違いしたものだろうと考えています。
ただ、微弱な無変調のキャリアを受信したというレポートがあるけれども
それはStenSatからのものかもしれないと言っています。
Hankは、StenSatからのAX.25のパケットが聞こえてこないことがどうしても
おかしいと考えているようです。
正常ならば、StenSatは、バッテリーの放電状態から目覚めたとき、あるいは
ワッチドッグタイマーが働いてリセットが掛かったあとでは、テレメトリモード
に入ります。このモードでは、5秒おきにAX.25のパケットを送信します。
(JJ1WTK補足:パケットは1200bpsAFSKで、周波数は436.625MHz)
StenSatの動作テストをした頃、かなり後の時期にオーディオミキサーに変更を
加えました。コントローラーユニットからのAX.25とCWのテレメトリを送信機に
供給するようにしたのです。この回路が異常を起こして、テレメトリは送出されず、
代わりに無変調のキャリアだけが送信されているのかも知れません。
この仮説を確かめるために、みなさんの協力をお願いしたいのです。できるかた
は、StenSatにDTMFコマンドを送って、テレメトリモードからボイストランスポン
ダモードに切り替えてください。トランスポンダモードに切り替われば、レーピ
ターのように使ってみてください。トランスポンダモードに切り替えるDTMFコマ
ンドは、
"#6676326"
です。
(JJ1WTK補足:アップリンク周波数は、145.840MHzです。StenSatのDTMFデコーダ
のタイムアウトは8秒ですから、8秒以内にコマンドトーンを送り終えることです)
Forwarded by JJ1WTK Kazu Sakamoto <jj1wtk@jamsat.or.jp>
---------------- Original message follows ----------------
From: Hank Heidt <hheidt@erols.com>
To: amsat-bb@AMSAT.Org
Cc: James Cutler <jwc@Stanford.EDU>
Date: Mon, 14 Feb 2000 15:49:42 -0500
Subject: [amsat-bb] StenSat - something to try...
--
Hi,
Discounting signal reports that appear to be spurious local emissions,
there have been a few reports of stations copying a weak signal that is not
modulated.
Nominally StenSat should power up in telemetry mode after every watch dog
reset or battery discharge. In this mode StenSat transmits a AX.25 packet
every 5 seconds and the output of the receiver is squelched.
During testing of StenSat we made some rather late changes to the audio
mixer that feeds the AX.25 and CW telemetry from the controller unit to the
transmitter. It may be possible that this circuit has failed and that no
telemetry is being transmitted but that an un-modulated carrier is being
transmitted instead. To test this theory, i'd like request that stations
try to place StenSat into voice transponder mode by issuing the DTMF
command below and then transmitting a modulated uplink signal.
The DTMF command for placing StenSat into transponder (repeater) mode is:
"#6676326"
Thanks for all the help and support.
-Hank Heidt N4AFL
http://www.erols.com/hheidt
----
Via the amsat-bb mailing list at AMSAT.ORG courtesy of AMSAT-NA.
To unsubscribe, send "unsubscribe amsat-bb" to Majordomo@amsat.org